MENGXING THERMOFORMING MACHINE ON 2024 CHINAPLAS
Common vacuum forming machine
High speed vacuum vacuum characteristics and blister molding machine and injection molding
by：Mengxing
2020-07-18
A, the characteristics of vacuum vacuum molding machine machine:
1, the vertical pull piece of design: pull uniformity and stability of fast, shorten the holding time, the environmental protection material more adaptability and lower power consumption, ensure the quality of product molding.
2, grouping independent temperature control: adopt special dense plane far-infrared ceramic hair piece assembly, temperature uniformity, 50% higher than traditional machine save electricity.
3, electrothermal furnace adopts enclosed heating, the heating more even and reducing heat loss, and comes with a manual switch, vertical lift, control of electric furnace in the process of production, control product quality. Thick film or PP sheet can adopt double electric furnace heating up and down, Customer order) To speed up the heating time, improve production speed.
4, this machine is equipped with vibration membrane device, for complex product is not easy to deformation, demoulding easy.
5, double row needle chain transmission, high speed to ensure a stable, accurate and with a width adjustable device, make the best use of mechanical energy of film and reduce waste.
6, the whole machine is equipped with water cooling device and high-speed cold water spray, speed up the molding and ensure the quality of molding, production speed is faster than the traditional one times.
7, built-in secondary vacuum, the difficult of products are more likely to molding, improve product quality, reduce scrap rate.
8, the whole machine adopts imported equipment and international pneumatic components factory, quality is absolutely reliable, safe and durable.
1. If the material price is the same, the cost of blister low
2. Blister forming machine is already processing and molding of plastic sheet, the mould is according to the product style is made of gypsum auxiliary forming, and then on a layer of copper plating with durable, a version of the copper price is about 1000 yuan;
with injection molded plastic raw materials ( Particles) , the mold must be based on the software design ( General use CAD) When the parameters of the production, production requirements down to poor, a version of the hardware mold injection molding with the simplest also want 2 - More than 3000, complex to tens to hundreds of thousands of.
1, the vertical pull piece of design: pull uniformity and stability of fast, shorten the holding time, the environmental protection material more adaptability and lower power consumption, ensure the quality of product molding.
2, grouping independent temperature control: adopt special dense plane far-infrared ceramic hair piece assembly, temperature uniformity, 50% higher than traditional machine save electricity.
3, electrothermal furnace adopts enclosed heating, the heating more even and reducing heat loss, and comes with a manual switch, vertical lift, control of electric furnace in the process of production, control product quality. Thick film or PP sheet can adopt double electric furnace heating up and down, Customer order) To speed up the heating time, improve production speed.
4, this machine is equipped with vibration membrane device, for complex product is not easy to deformation, demoulding easy.
5, double row needle chain transmission, high speed to ensure a stable, accurate and with a width adjustable device, make the best use of mechanical energy of film and reduce waste.
6, the whole machine is equipped with water cooling device and high-speed cold water spray, speed up the molding and ensure the quality of molding, production speed is faster than the traditional one times.
7, built-in secondary vacuum, the difficult of products are more likely to molding, improve product quality, reduce scrap rate.
8, the whole machine adopts imported equipment and international pneumatic components factory, quality is absolutely reliable, safe and durable.
1. If the material price is the same, the cost of blister low
2. Blister forming machine is already processing and molding of plastic sheet, the mould is according to the product style is made of gypsum auxiliary forming, and then on a layer of copper plating with durable, a version of the copper price is about 1000 yuan;
with injection molded plastic raw materials ( Particles) , the mold must be based on the software design ( General use CAD) When the parameters of the production, production requirements down to poor, a version of the hardware mold injection molding with the simplest also want 2 - More than 3000, complex to tens to hundreds of thousands of.
Custom message
Related Products
