MENGXING THERMOFORMING MACHINE ON 2024 CHINAPLAS
Common vacuum forming machine
The characteristics of high speed vacuum vacuum forming machine and daily use pay attention to the problem
by：Mengxing
2020-07-16
The characteristics of high speed vacuum vacuum forming machine is as follows:
1. This machine is equipped with vibration membrane device, for complex product is not easy to deformation, demoulding;
2. The whole machine adopts imported equipment and international pneumatic components factory, quality is absolutely reliable, safe and durable;
3. Built-in set two vacuum, make difficult products are more likely to molding, improve product quality, reduce scrap rate;
4. Independently grouped temperature control: the use of special dense plane far-infrared ceramic chip assembly, temperature uniformity, 50% higher than traditional machine save electricity.
5. The machine is equipped with water cooling device and high-speed cold water spray, speed up the molding and ensure the quality of molding, production speed is faster than the traditional one times;
6. Double row needle chain transmission, high-speed operation to ensure accurate and stable, with a width adjustable device, make the best use of mechanical energy of film, reduce the waste;
7. USES vertical pull piece of design: pull uniformity and stability of fast, shorten the holding time, the environmental protection material more adaptability and lower power consumption, ensure the quality of molding products;
8. Adopting the enclosed heating, electric heating furnace heating more even and reducing heat loss, and comes with a manual switch, vertical lift, control of electric furnace in the process of production, control product quality. Thick film or PP sheet can be used up and down double electric furnace heating speeds up the heating time, improve production speed;
daily use vacuum molding machine problems
plastic packaging market now has developed into the with the increase of molding, sheet thickness, cooling, increases correspondingly, so the artificial cooling method must be used to shorten the cycle. As mentioned above, the cooling way two kinds of common cold inside and outside cold, they can be used alone, also can use a combination of, it should be according to the need of the products. But because of outside cooling easy and is often used.
vacuum molding machine ideally parts in contact with the mould of the inner surface and outer surface cooling, had better use the built-in cooling coil and mold. For non-metallic mold, such as wood, plaster, glass fiber reinforced plastic.
1. This machine is equipped with vibration membrane device, for complex product is not easy to deformation, demoulding;
2. The whole machine adopts imported equipment and international pneumatic components factory, quality is absolutely reliable, safe and durable;
3. Built-in set two vacuum, make difficult products are more likely to molding, improve product quality, reduce scrap rate;
4. Independently grouped temperature control: the use of special dense plane far-infrared ceramic chip assembly, temperature uniformity, 50% higher than traditional machine save electricity.
5. The machine is equipped with water cooling device and high-speed cold water spray, speed up the molding and ensure the quality of molding, production speed is faster than the traditional one times;
6. Double row needle chain transmission, high-speed operation to ensure accurate and stable, with a width adjustable device, make the best use of mechanical energy of film, reduce the waste;
7. USES vertical pull piece of design: pull uniformity and stability of fast, shorten the holding time, the environmental protection material more adaptability and lower power consumption, ensure the quality of molding products;
8. Adopting the enclosed heating, electric heating furnace heating more even and reducing heat loss, and comes with a manual switch, vertical lift, control of electric furnace in the process of production, control product quality. Thick film or PP sheet can be used up and down double electric furnace heating speeds up the heating time, improve production speed;
daily use vacuum molding machine problems
plastic packaging market now has developed into the with the increase of molding, sheet thickness, cooling, increases correspondingly, so the artificial cooling method must be used to shorten the cycle. As mentioned above, the cooling way two kinds of common cold inside and outside cold, they can be used alone, also can use a combination of, it should be according to the need of the products. But because of outside cooling easy and is often used.
vacuum molding machine ideally parts in contact with the mould of the inner surface and outer surface cooling, had better use the built-in cooling coil and mold. For non-metallic mold, such as wood, plaster, glass fiber reinforced plastic.
Custom message
Related Products
